STEP UP DCDC CONVERTOR IP. 10-60V OP. 12-80V 1200W

<p><span style=”font-family:Arial,Helvetica,sans-serif;”><strong style=”font-family: Arial, Helvetica, sans-serif;”><span style=”font-size:18px;”>Feature &amp;&nbsp;</span></strong><span style=”font-size: 18px;”><strong>Specification</strong></span></span></p>

<ul>
<li>
<p><span style=”font-family:Arial,Helvetica,sans-serif;”><span style=”font-size:14px;”>Input voltage: 8-60V</span></span></p>
</li>
<li>
<p><span style=”font-family:Arial,Helvetica,sans-serif;”><span style=”font-size:14px;”>Input Current: 20A</span></span></p>
</li>
<li>
<p><span style=”font-family:Arial,Helvetica,sans-serif;”><span style=”font-size:14px;”>Quiescent current: 15mA (12V liter 20V, the output voltage, the higher the current will increase too quiet)</span></span></p>
</li>
<li>
<p><span style=”font-family:Arial,Helvetica,sans-serif;”><span style=”font-size:14px;”>Output voltage: 12-83V</span></span></p>
</li>
<li>
<p><span style=”font-family:Arial,Helvetica,sans-serif;”><span style=”font-size:14px;”>Maximum Output Current: 20A (Over 15A, please enhance heat dissipation)</span></span></p>
</li>
<li>
<p><span style=”font-family:Arial,Helvetica,sans-serif;”><span style=”font-size:14px;”>Constant Range: 0.5 – 20A</span></span></p>
</li>
<li>
<p><span style=”font-family:Arial,Helvetica,sans-serif;”><span style=”font-size:14px;”>Working temperature: -40 to + 85&deg;C</span></span></p>
</li>
<li>
<p><span style=”font-family:Arial,Helvetica,sans-serif;”><span style=”font-size:14px;”>Operating frequency: 150KHz</span></span></p>
</li>
<li>
<p><span style=”font-family:Arial,Helvetica,sans-serif;”><span style=”font-size:14px;”>Conversion efficiency: up to 95% (efficiency and input and output voltage, current, pressure-related)</span></span></p>
</li>
<li>
<p><span style=”font-family:Arial,Helvetica,sans-serif;”><span style=”font-size:14px;”>Overcurrent protection: Yes (with reduced flow adjustment, adjustable output current limit, current exceeds the current limit, the output current is automatically reduced to a minimum 5A, vary according to the nature of the load current will be.)</span></span></p>
</li>
<li>
<p><span style=”font-family:Arial,Helvetica,sans-serif;”><span style=”font-size:14px;”>Short circuit protection: Yes&nbsp;</span></span></p>
</li>
<li>
<p><span style=”font-family:Arial,Helvetica,sans-serif;”><span style=”font-size:14px;”>Input reverse polarity protection: NO</span></span></p>
</li>
<li>
<p><span style=”font-family:Arial,Helvetica,sans-serif;”><span style=”font-size:14px;”>Output Counter filling: Yes, for charging plus blocking diode is not required.</span></span></p>
</li>
<li>
<p><span style=”font-family:Arial,Helvetica,sans-serif;”><span style=”font-size:14px;”>Installation: four 3mm screws</span></span></p>
</li>
<li>
<p><span style=”font-family:Arial,Helvetica,sans-serif;”><span style=”font-size:14px;”>Connection: solderless terminals output</span></span></p>
</li>
<li>
<p><span style=”font-family:Arial,Helvetica,sans-serif;”><span style=”font-size:14px;”>Module dimensions (mm): 116 * 52 * 15</span></span></p>
</li>
</ul>

<p>&nbsp;</p>

<p><span style=”font-family:Arial,Helvetica,sans-serif;”><span style=”font-size:18px;”><strong>When using the boost power supply should pay attention to the following points:&nbsp;</strong></span></span></p>

<ol>
<li>
<p><span style=”font-family:Arial,Helvetica,sans-serif;”><span style=”font-size:14px;”>Input power supply voltage must be above 10V.</span></span></p>
</li>
<li>
<p><span style=”font-family:Arial,Helvetica,sans-serif;”><span style=”font-size:14px;”>When the power supply is used for the input power supply, the input power and the output voltage of the input power supply are the first to be unloaded. Then pick up the load. (must ensure that the switching power supply has been working).</span></span></p>
</li>
<li>
<p><span style=”font-family:Arial,Helvetica,sans-serif;”><span style=”font-size:14px;”>When the constant current mode is used to set the voltage, the constant voltage must be higher than the input voltage. Do not use the way of short circuit output current, the circuit structure of the boost module can not be adjusted in short circuit way.</span></span></p>
</li>
<li>
<p><span style=”font-family:Arial,Helvetica,sans-serif;”><span style=”font-size:14px;”>If the input voltage fluctuation range is lower than the set output voltage, then the output voltage is constant, it is to ensure that input is lower than the output voltage.</span></span></p>
</li>
</ol>